Home/Technologies/How Plasma Cutting Works: Process, Equipment, and Quality Tips
Technologies

How Plasma Cutting Works: Process, Equipment, and Quality Tips

Plasma cutting uses an electric arc to turn gas into plasma, enabling precise metal cuts on steel, aluminum, and more. Learn how it works, what affects cut quality, and how to choose the right cutter and compressor for your needs.

Nov 16, 2026
10 min
How Plasma Cutting Works: Process, Equipment, and Quality Tips

Plasma cutting is a versatile method used to cut brackets from steel sheets, shorten profile pipes, or shape complex CNC workpieces. The core of these operations is one process: an electric arc transforms a stream of gas into plasma, which the plasma torch focuses into a narrow cutting zone. Ordinary compressed air often serves as the gas.

The capabilities of a plasma cutter depend on the material, workpiece thickness, and edge quality requirements. The same device can deliver a clean cut on one thickness but leave a bevel or dross on thicker metal. To understand why, let's start by looking at what happens inside the plasma torch.

How a Plasma Cutter Works

How the Electric Arc Turns Gas into Plasma

A plasma cutter consists of a power supply and a plasma torch into which gas is fed. Inside the torch are an electrode and a nozzle with a small outlet. A work cable with a clamp is connected to the metal workpiece, closing the circuit when the operating arc burns between the electrode and the workpiece.

In many machines, an auxiliary or pilot arc is first ignited between the electrode and the nozzle. This arc heats and partially ionizes the gas passing through the torch. During ionization, some molecules and atoms lose electrons, creating free electrons and ions that allow the gas to conduct electric current. This ionized gas is called plasma.

When the jet reaches the workpiece, the arc transfers to the metal. During cutting, the main arc burns between the internal electrode and the workpiece, directing energy precisely to the cutting area. For this method, the workpiece must be conductive-steel and aluminum work, but glass and wood do not.

The nozzle's job is to constrict the arc and direct the gas flow along its axis. This concentrates energy on a small area, and the gas exits the nozzle at high speed. The nozzle hole shape affects the jet's form, so wear over time increases cut width and alters edge angles.

How the Plasma Jet Cuts Metal

The arc locally heats and melts the metal. The fast-moving gas jet blows molten metal out of the kerf, clearing the way for the cut to continue. As the torch moves, this process repeats along the entire line. You can see a stream of sparks at the exit-these are hot metal droplets ejected from the cut zone.

If the cut starts at the sheet edge, molten metal exits through the open end immediately. When piercing a hole in the middle, the torch must first break through the full thickness. Until there's a through-hole, some melt is expelled upward toward the nozzle. This is why maximum piercing thickness is often listed separately from edge-start cutting thickness in machine specifications.

Kerf width also depends on how long the arc dwells on each section. Too slow, and metal melts beyond the cut line, possibly leaving dross on the lower edge. Too fast, and the bottom lags behind the top, potentially leaving uncut spots. Cutting charts for different materials and thicknesses specify speed along with current for this reason.

What Metals Can Be Plasma Cut and How Thick?

Carbon Steel, Stainless, and Aluminum

Standard plasma cutters are designed for conductive metals, including carbon steel, stainless steel, aluminum, copper, and brass. Each material requires its own settings. Even sheets of the same thickness may need different speeds due to how each metal conducts heat and behaves when molten.

Carbon steel is often cut with air plasma cutters, allowing for sheet fabrication, pipe trimming, and template cutting. When cutting angles or profile tubes, use the wall thickness at the cut as your setting reference. For instance, for a 40 × 40 × 3 mm tube, base your settings on 3 mm. At corners, carefully monitor the torch's distance to the metal.

For stainless steel, consider post-cut edge quality. If the part will be welded or remain visible, you may need to remove oxide layers and heat marks. Industrial setups select plasma gas composition based on steel grade, thickness, and desired edge finish.

Cutting aluminum requires settings tailored to the metal. Aluminum dissipates heat quickly, so steel settings for the same thickness may yield different kerfs and edges. If the manufacturer provides an aluminum-specific table, use it to check current, speed, and torch-to-sheet distance.

Working Thickness, Maximum Cut, and Piercing Capacity

A "cuts up to 20 mm" claim alone says little about actual performance. Always check which metal is referenced and whether the number refers to working cut, maximum separation, or piercing capability.

  • Working thickness is the recommended operating thickness for routine cutting. If parts must fit together right after cutting, consult the settings table and make a test cut on scrap. This lets you assess bevel, dross, and finishing requirements.
  • Maximum thickness is what the cutter can still separate. At this limit, you'll likely need to slow down and the lower edge may be rougher. This mode is suitable for trimming thick stock for later finishing, but for regular work, use the working thickness.
  • Piercing thickness matters when starting cuts within the sheet-important for holes and closed CNC contours. For example, if a cutter lists 16 mm working cut, 22 mm max cut, and 12 mm piercing, you can cut 16 mm from the edge. To start inside a 16 mm sheet, you'll need a pre-drilled starter hole or a machine with higher piercing capacity.

How to Choose a Plasma Cutter and Compressor

Handheld Plasma Cutters and CNC Machines

Handheld plasma cutters are great for trimming profiles, cutting brackets, or slicing sheets with a guide. For straight cuts, use a metal ruler; for repetitive shapes, use a template. In both cases, speed and torch position depend on the operator. If you slow down at a corner, the kerf may widen there.

A CNC machine guides the torch along a programmed path, maintains steady speed on straight sections, and repeats contours for batches. With automatic height control, the system keeps the correct distance as the sheet warps from heat-ideal for mass production, complex shapes, and series of holes.

When choosing a plasma cutter for a garage or workshop, start with the metal you'll cut most. For regular cuts in 4-6 mm sheet, check the cutter's speed in that range and the required current per the manufacturer's chart. There may be several settings for one thickness-each with its own consumables, speed, and cutting height. Stick to parameters from the same table row.

For long cuts, duty cycle (DC) is crucial. For example, a DC of 40% at 50 A means the machine is rated for four minutes' work in a ten-minute cycle at that current. If you often cut large sheets, compare DCs at your intended current across models.

Which Gas to Use and Choosing a Compressor

Handheld plasma cutters commonly use compressed air, supplied by an external or built-in compressor. Industrial setups may use oxygen, nitrogen, or gas mixtures, depending on system, metal, and edge requirements. Approved gases and modes appear in the machine's documentation.

To pick a compressor, check the plasma cutter's manual for required air flow and inlet pressure. The compressor must supply the necessary volume at working pressure as long as the torch is in use. Compare your cutter's requirements to the compressor's output. If only intake volume is listed, it may not be enough for long cuts.

Receiver (tank) size determines stored air volume-enough for several short cuts. If the torch consumes air faster than the compressor refills, pressure will drop. Check pressure at the machine's inlet with air flowing. Long, narrow hoses or small fittings can reduce pressure, even with an adequate compressor.

Clean, dry air is essential. Condensate collects in the receiver and can enter the torch, hastening electrode and nozzle wear. Drain condensate regularly and use a filter-dryer. If oil or moisture remains, adjust your air preparation system to meet machine requirements.

What Affects Plasma Cutting Quality?

Why Dross and Bevels Occur

Dross-solidified droplets of molten metal-forms on the lower cut edge. Slow travel tends to create large, rounded beads that are easy to knock off. Fast travel produces thin, tightly adhering dross with drag lines slanting backward, indicating speed is too high. These clues help adjust your settings.

If dross appears mainly at corners or tight curves, check for excessive torch slow-down in those spots. On straights, speed may be fine, but at turns, the arc lingers and the kerf widens, collecting melt at the exit. This happens in manual cutting when the operator pauses to reposition the torch or hand.

Bevel occurs when the cut face is not perpendicular. In manual work, first check torch verticality-a tilted nozzle sends the jet through the sheet at an angle. Too much torch-to-workpiece distance allows the jet to flare, making the kerf wider at the top than the bottom.

Even at correct height, one kerf side may be straighter than the other due to gas swirl inside the torch-important in CNC cutting. Set the cutting direction so the less beveled edge remains on the part and the more beveled side is scrap.

When to Replace Nozzle and Electrode

Check nozzle condition by inspecting the outlet. A good nozzle has a round hole with smooth edges. If it becomes oval, enlarges, or develops notches, the jet loses symmetry. You'll see this as wider cuts, rougher drag lines, or new bevels despite unchanged settings.

The electrode's working surface develops a pit as it wears. A small crater is normal, but replace the electrode when it reaches the manufacturer's depth limit. Severely worn electrodes can cause arc ignition problems and damage the nozzle. Always check both parts during maintenance.

If cut quality drops mid-batch, inspect consumables and check airflow at working consumption. Then make a short test cut on scrap. Change only one parameter at a time-leave current and height the same, and test how speed affects dross. This helps isolate what adjustment works.

Plasma vs. Laser and Waterjet Cutting

Plasma cutting is often chosen for rapid steel sheet fabrication, especially when parts will be finished or welded later. Laser cutting excels for fine features and precise fitting. Waterjet is ideal for heat-sensitive blanks and materials like stone or glass, which plasma can't cut.

Laser cutting uses a focused beam to heat metal, assisted by gas to clear material from the kerf. On thin sheets, lasers provide narrower cuts and better reproduce small holes, slots, and sharp corners-for example, vent panels or intricate grids. For large steel blanks destined for welding, plasma is often sufficient. Speed for both methods depends on sheet thickness and machine power.

Waterjet cutting uses a high-pressure water stream with abrasive particles, removing material mechanically and leaving no heat-affected zone along the edge. Plasma and laser do create such zones, which can alter metal properties or cause warping, especially in thin, densely cut sheets. For more details, see our article on how waterjet cutting shapes metal, stone, and glass with high-pressure water.

Waterjet is usually slower than plasma for steel, especially when a smooth edge is needed. Higher feed rates cause the jet to lag at the bottom, leaving visible striations. If a part must fit immediately after cutting, balance cutting time with finishing needs-fast cuts often require edge cleanup and hole fitting, while slower methods may deliver the desired geometry in a single pass.

Conclusion

In plasma cutting, an electric arc turns gas into conductive plasma, melting metal along the cut line. The gas jet blows away the molten pool. This method is ideal for quick cutting of steel, stainless, and aluminum when minor edge bevels and post-processing are acceptable.

To choose a plasma cutter, identify your material, working thickness, and acceptable bevel. If starting cuts inside a sheet, check the rated piercing thickness. For air plasma, match required flow and pressure to compressor performance. Before processing a batch, make a test cut on scrap to gauge finishing time and edge quality.

Tags:

plasma cutting
metal fabrication
cutting equipment
steel cutting
cnc machines
air compressor
cutting quality
laser vs plasma

Similar Articles

Loading...